This site uses cookies. By continuing to browse the ConceptDraw site you are agreeing to our Use of Site Cookies.
The vector stencils library "HVAC controls" contains 23 symbols of HVAC controls (sensors, actuators, timers, controllers, I/ O points). Use it for drawing HVAC system diagrams, controls drawings, and automated building control and environmental control systems design.
The example "HVAC controls - Vector stencils library" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the HVAC Plans solution from the Building Plans area of ConceptDraw Solution Park.
Temperature
Temperature, temperature sensor,
Humidity
Humidity, humidity sensor,
Enthalpy
Enthalpy, enthalpy sensor,
Pressure
Pressure, pressure sensor,
Flow
Flow, flow sensor, water, air,
Velocity
Velocity, velocity sensor, water, air,
Voltage
Voltage, voltage sensor,
General
General, sensor,
Light
Light, light sensor,
Rotation
Rotation, equipment rotation sensor, rotation sensor,
Vibration
Vibration, equipment vibration sensor, vibration sensor,
Timer
Timer, timer, time clock,
Current
Current, current sensor,
Power
Power, power sensor,
Air quality
Air quality, air quality sensor,
Level
Level, fluid, level,
End switch
End switch, end switch, limit switch,
Smoke
Smoke, smoke detector,
Power connection
Power connection, power connection,
Actuator
Actuator, actuator,
I/O point
I/O point, input, output, point,
Label
Label,
Wire note
Wire note,
The vector stencils library Alarm and access control contains 80 symbols of digital proximity equipment, locking hardware, and access control equipment.
"An alarm device or system of alarm devices gives an audible, visual or other form of alarm signal about a problem or condition. Alarm devices are often outfitted with a siren." [Alarm device. Wikipedia]
"An access control point, which can be a door, turnstile, parking gate, elevator, or other physical barrier, where granting access can be electronically controlled. Typically, the access point is a door. An electronic access control door can contain several elements. At its most basic, there is a stand-alone electric lock. The lock is unlocked by an operator with a switch. To automate this, operator intervention is replaced by a reader. The reader could be a keypad where a code is entered, it could be a card reader, or it could be a biometric reader. Readers do not usually make an access decision, but send a card number to an access control panel that verifies the number against an access list. To monitor the door position a magnetic door switch can be used. In concept, the door switch is not unlike those on refrigerators or car doors. Generally only entry is controlled, and exit is uncontrolled. In cases where exit is also controlled, a second reader is used on the opposite side of the door. In cases where exit is not controlled, free exit, a device called a request-to-exit (REX) is used. Request-to-exit devices can be a push-button or a motion detector. When the button is pushed, or the motion detector detects motion at the door, the door alarm is temporarily ignored while the door is opened. Exiting a door without having to electrically unlock the door is called mechanical free egress. This is an important safety feature. In cases where the lock must be electrically unlocked on exit, the request-to-exit device also unlocks the door." [Access control. Wikipedia]
Use the design elements library Alarm and access control for drawing layout floor plans, blueprints, and wiring diagrams of intrusion systems, time and attendance systems, card and code access control security systems, internal and external security control systems using the ConceptDraw PRO diagramming and vector drawing software.
The shapes library Alarm and access control is included in the Security and Access Plans solution from the Building Plans area of ConceptDraw Solution Park.
Alarm and access control symbols
Alarm and access control symbols, window contact sensor, weatherproof, horn, siren, wall motion sensor, motion sensor, volumetric capacity detector, vibration sensor, shock sensor, vehicle loop detector, user control keyswitch, user control digital keypad, ultrasonic transceiver, turnstile, transformer, traffic arm, strobe, space detection device, smoke detector, slave tape dialer, slave digital communicator, siren, security window screen, security keypad, security door contact, security control unit, security control panel, security card reader, screen alarm, revolving door, remote zone annunciator, receiver, pushbutton, passive infrared, panic button, overhead door contact sensor, door contact sensor, motion detector, microwave transceiver, master intercom, mains supply power source, magnetic lock, security door alarm, line cut monitor, keypad device, keypad, intercom unit, infrasonic, infrared detector, horn, strobe, horn, siren, heat detector, glass break detector, gas detector, foil on glass detector, foil, floor motion sensor, motion sensor, floor mat, flood sensor, exit device, emergency power, emergency battery, electronic lock, electric door strike, electric door opener, dual technology device, driveway sensor, doorbell, door contact sensor, door chime, door buzzer, dial-up remote equipment, control unit, contact switch surface, contact switch flush, card reader, time, attendance, card reader, keypad, card access reader, card access, carbon monoxide detector, CO detector, camera, keypad, camera, intercom, camera, card reader, camera, biometric access reader, biometric access, beam fence disturbance, PIR field of view,
The vector stencils library "HVAC controls" contains 23 symbols of HVAC controls (sensors, actuators, timers, controllers, I/ O points).
"HVAC (... Heating, Ventilation and Air Conditioning) is a control system that applies regulation to a heating and/ or air conditioning system. ...
Central controllers and most terminal unit controllers are programmable, meaning the direct digital control program code may be customized for the intended use. The program features include time schedules, setpoints, controllers, logic, timers, trend logs, and alarms. The unit controllers typically have analog and digital inputs that allow measurement of the variable (temperature, humidity, or pressure) and analog and digital outputs for control of the transport medium (hot/ cold water and/ or steam). Digital inputs are typically (dry) contacts from a control device, and analog inputs are typically a voltage or current measurement from a variable (temperature, humidity, velocity, or pressure) sensing device. Digital outputs are typically relay contacts used to start and stop equipment, and analog outputs are typically voltage or current signals to control the movement of the medium (air/ water/ steam) control devices such as valves, dampers, and motors." [HVAC control system. Wikipedia]
Use the design elements library "HVAC controls" for drawing the HVAC system diagrams, controls drawings, and automated building control and environmental control system layuout floor plans using the ConceptDraw PRO diagramming and vector drawing software.
The shapes example "Design elements - HVAC controls" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the HVAC Plans solution from the Building Plans area of ConceptDraw Solution Park.
HVAC control symbols
HVAC control symbols, voltage sensor, velocity sensor, water, air, timer, time clock, temperature sensor, smoke detector, sensor, pressure sensor, power sensor, power connection, light sensor, input, output, point, humidity sensor, fluid, level, flow sensor, water, air, equipment vibration sensor, vibration sensor, equipment rotation sensor, rotation sensor, enthalpy sensor, end switch, limit switch, current sensor, air quality sensor, actuator,