Products Solutions Samples Buy
✕
This site uses cookies. By continuing to browse the ConceptDraw site you are agreeing to our Use of Site Cookies.
Try ConceptDraw Free
The vector stencils library "Valves" contains 91 symbols of piping and plumbing valves.
"A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically valves fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure.
The simplest, and very ancient, valve is simply a freely hinged flap which drops to obstruct fluid (gas or liquid) flow in one direction, but is pushed open by flow in the opposite direction. This is called a check valve, as it prevents or "checks" the flow in one direction.
People in developed nations use valves in their daily lives, including plumbing valves, such as taps for tap water, gas control valves on cookers, small valves fitted to washing machines and dishwashers, safety devices fitted to hot water systems..." [Valve. Wikipedia]
Use the design elements library "Valves" to draw building plans, schematic diagrams, blueprints, or technical drawings of industrial piping systems; process, vacuum, and fluids piping; hydraulics piping; air and gas piping; materials distribution; and liquid transfer systems using the ConceptDraw PRO diagramming and vector drawing software.
The shapes library "Valves" is included in the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park.
Valve symbols
Valve symbols, weight loaded, actuating method, wedge gate valve, wedge valve, valve, statically loaded, actuating method, spring loaded, actuating method, solenoid, screw-down valve, lock-shield valve, reel valve, valve, remotely controlled, actuating method, relief valve, valve, relief angle valve, relief valve, angle valve, valve, pressure, vacuum, regulating, method of control, reducing valve, valve, quick, open, close, opening, closing, powered valve, valve, power signal, plug valve, valve, piston, parallel slide valve, parallel valve, valve, needle valve, valve, motor element, mixing valve, valve, manual isolation, in-line valve, valve, globe valve, valve, gear operated, actuating method, gate valve, valve, float operated, actuating method, float operated valve, valve, flanged valve, valve, diaphragm, actuating method, diaphragm valve, valve, dash-pot, connecting unit, check valve, valve, characterized port valve, valve, chain operated, actuating method, butterfly valve, valve, ball valve, valve, angle valve, valve, 3-way plug valve, plug valve, valve,
Used Solutions

Piping and Instrumentation Diagram Software

Piping and Instrumentation Diagram Software
Piping and Instrumentation Diagram is a technical sketch or drawing, which shows in details the piping system and instrumentation of a processing plant. Piping and Instrumentation Diagram is developed by process design engineers and technical engineers on the phase of plant design. This plan is necessary on the stages of plant construction and then is actively used by operators, instrumentation and piping engineers when operating the plant. ConceptDraw DIAGRAM software provides unique Plumbing and Piping Plans solution from Building Plans area of ConceptDraw Solution Park with 10 libraries of ready-to-use predesigned vector elements, templates and samples, to help you create professional Piping diagrams and schematics, Instrumentation diagrams, Plumbing plans and blueprints, Schemes of hot and cold water supply systems, Heating schemes, Mechanical diagrams, Diagrams of fluids, hydraulics, air and gas pipings, Technical drawings of waste water disposal systems, Schematics of industrial piping systems, Diagrams of ventilation systems, etc.

Interior Design. Piping Plan — Design Elements

The pipe laying and setting the plumbing system at new apartment or home, or replacing the worn plumbing begins from the choice of materials, sizes of pipes and creation the plan. When developing a piping system, the engineer should take into account many aspects, such as advantages and disadvantages of different pipes materials, the temperature changes (freezing or thermal expansion) that effect on pipes. The most commonly used are steel pipes which have passed the test of time, but they are difficult for assembling and prone to corrosion, plastic (polypropylene) pipes that are characterized by low weight and price, ease of installation and durability, and also PEX-AL-PEX pipes. Numerous libraries with ready-to-use design elements of pipes, valves and other plumbing and piping equipment included to Plumbing and Piping Plans solution for ConceptDraw DIAGRAM help easy design Piping and Plumbing interior design plans, blueprints, schematic diagrams, technical drawings of waste water disposal systems, hot and cold water supply systems.
The vector stencils library "Valves" contains 91 symbols of valves. Use it for drawing plumbing and piping plans, schematic diagrams and blueprints of industrial piping systems; process, vacuum, and fluids piping; hydraulics piping; air and gas piping; materials distribution; and liquid transfer systems in the ConceptDraw PRO diagramming and vector drawing software extended with the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park.
In-line valve
In-line valve, in-line valve, valve,
3-way valve
3-way valve, in-line valve, valve,
4-way valve
4-way valve, in-line valve, valve,
Screw-down valve
Screw-down valve, screw-down valve, lock-shield valve, reel valve, valve, stop cock,
Lock-shield valve
Lock-shield valve, screw-down valve, lock-shield valve, reel valve, valve,
Reel valve
Reel valve, screw-down valve, lock-shield valve, reel valve, valve,
Relief valve
Relief valve, relief valve, valve,
Relief valve 2
Relief valve 2, relief valve, valve,
Relief valve 3
Relief valve 3, relief valve, valve,
Relief valve 4
Relief valve 4, relief valve, valve,
Angle valve
Angle valve, angle valve, valve,
Angle valve 2
Angle valve 2, angle valve, valve,
Angle valve 3
Angle valve 3, angle valve, valve,
Angle valve 4
Angle valve 4, angle valve, valve,
Check valve
Check valve, check valve, valve,
Check valve 2
Check valve 2, check valve, valve,
Screwdown valve
Screwdown valve, check valve, valve,
Float operated valve
Float operated valve, float operated valve, valve,
Float operated valve 2
Float operated valve 2, float operated valve, valve,
Flanged valve
Flanged valve, flanged valve, valve,
Flanged valve 2
Flanged valve 2, flanged valve, valve,
Butterfly valve
Butterfly valve, butterfly valve, valve,
Butterfly valve 2
Butterfly valve 2, butterfly valve, valve,
Globe valve
Globe valve, globe valve, valve,
Globe valve 2
Globe valve 2, globe valve, valve,
Globe valve 3
Globe valve 3, globe valve, valve,
Needle valve
Needle valve, needle valve, valve,
Needle valve 2
Needle valve 2, needle valve, valve,
Needle valve 3
Needle valve 3, needle valve, valve,
Needle valve 4
Needle valve 4, needle valve, valve,
Diaphragm valve
Diaphragm valve, diaphragm valve, valve,
Diaphragm valve 2
Diaphragm valve 2, diaphragm valve, valve,
Diaphragm valve 3
Diaphragm valve 3, diaphragm valve, valve,
Wedge gate valve
Wedge gate valve, wedge gate valve, wedge valve, valve,
Parallel side valve
Parallel side valve, parallel slide valve, parallel valve, valve,
Gate valve
Gate valve, gate valve, valve,
Ball valve
Ball valve, ball valve, valve,
Ball valve 2
Ball valve 2, ball valve, valve,
Ball valve 3
Ball valve 3, ball valve, valve,
Powered control valve
Powered control valve, powered valve, valve,
Powered control valve 2
Powered control valve 2, powered valve, valve,
Powered control valve 3
Powered control valve 3, powered valve, valve,
Relief angle valve, pressure
Relief angle valve, pressure, relief angle valve, relief valve, angle valve, valve, pressure, vacuum,
Relief angle valve, vacuum
Relief angle valve, vacuum, relief angle valve, relief valve, angle valve, valve, pressure, vacuum,
Reducing valve
Reducing valve, reducing valve, valve,
Reducing valve 2
Reducing valve 2, reducing valve, valve,
Plug valve
Plug valve, plug valve, valve,
Plug valve 2
Plug valve 2,
Plug valve, straight through
Plug valve, straight through,
3-way plug valve
3-way plug valve, plug valve, valve,
Plug valve, T-port
Plug valve, T-port,
Plug valve, L-port
Plug valve, L-port,
3-way plug valve
3-way plug valve, 3-way plug valve, plug valve, valve,
3-way plug valve 2
3-way plug valve 2, 3-way plug valve, plug valve, valve,
3-way plug valve 3
3-way plug valve 3, 3-way plug valve, plug valve, valve,
3-way plug valve, T-port
3-way plug valve, T-port, 3-way plug valve, plug valve, valve,
3-way plug valve, L-port
3-way plug valve, L-port, 3-way plug valve, plug valve, valve,
Mixing valve
Mixing valve, mixing valve, valve,
Characterized port valve
Characterized port valve, characterized port valve, valve,
Manual isolation
Manual isolation, manual isolation,
Power signal
Power signal, power signal,
Statically loaded
Statically loaded, statically loaded, actuating method,
Spring loaded
Spring loaded, spring loaded, actuating method,
Spring loaded 2
Spring loaded 2, spring loaded, actuating method,
Remote control
Remote control, remotely controlled, actuating method,
Diaphragm
Diaphragm, diaphragm, actuating method,
Diaphragm, positioner
Diaphragm, positioner, diaphragm, actuating method,
Chain operated
Chain operated, chain operated, actuating method,
Gear operated
Gear operated, gear operated, actuating method,
Solenoid
Solenoid, solenoid,
Weight loaded
Weight loaded, weight loaded, actuating method,
Weight loaded 2
Weight loaded 2, weight loaded, actuating method,
Weight loaded 3
Weight loaded 3, weight loaded, actuating method,
Float operated
Float operated, float operated, actuating method,
Float operated 2
Float operated 2, float operated, actuating method,
Dash-pot
Dash-pot, dash-pot,
Dash-pot 2
Dash-pot 2, dash-pot,
Piston
Piston, piston,
Quick opening
Quick opening, quick, open, close, opening, closing,
Quick opening 2
Quick opening 2, quick, open, close, opening, closing,
Quick closing
Quick closing, quick, open, close, opening, closing,
Quick closing 2
Quick closing 2, quick, open, close, opening, closing,
Connecting unit
Connecting unit, connecting unit,
Connecting unit 2
Connecting unit 2, connecting unit,
Connecting unit 3
Connecting unit 3, connecting unit,
Motor element
Motor element, motor element,
Motor element, opens on failure
Motor element, opens on failure, motor element,
Motor element, closes on failure
Motor element, closes on failure, motor element,
Motor element, retains position on fail
Motor element, retains position on fail, motor element,
Motor element, safe direction
Motor element, safe direction, motor element,
Regulating
Regulating, regulating, method of control,
Used Solutions
The vector stencils library "Plumbing" contains 32 symbols of plumbing components and bathroom fixtures.
"Plumbing is the system of pipes, drains fittings, valves, valve assemblies, and devices installed in a building for the distribution of water for drinking, heating and washing, and the removal of waterborne wastes, and the skilled trade of working with pipes, tubing and plumbing fixtures in such systems. A plumber is someone who installs or repairs piping systems, plumbing fixtures and equipment such as water heaters and backflow preventers. The plumbing industry is a basic and substantial part of every developed economy due to the need for clean water, and sanitary collection and transport of wastes.
Plumbing is usually distinguished from water supply and sewage systems, in that a plumbing system serves one building, while water and sewage systems serve a group of buildings." [Plumbing. Wikipedia]
Use the design elements library "Plumbing" for drawing plumbing and piping plans, schematic diagrams and blueprints of waste water disposal systems, and hot and cold water supply systems using the ConceptDraw PRO diagramming and vector drawing software.
The shapes library "Plumbing" is included in the Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park.
Plumbing symbols
Plumbing symbols, water surface, washing machine, washer, towel rail, toilet, tank, sink unit, shower head, rotary pump, compressor, fan, pump, radiator, radiant panel, pump, pipe coils, heating coil, cooling coil, heater, cooler, end view, convector, boiler, tank, bath, basin,
Used Solutions
The vector stencils library "Valves and fittings" contains 104 symbols of valve components.
Use these icons for drawing industrial piping systems; process, vacuum, and fluids piping; hydraulics piping; air and gas piping; materials distribution; and liquid transfer systems.
"A valve is a device that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways. Valves are technically valves fittings, but are usually discussed as a separate category. In an open valve, fluid flows in a direction from higher pressure to lower pressure.
The simplest, and very ancient, valve is simply a freely hinged flap which drops to obstruct fluid (gas or liquid) flow in one direction, but is pushed open by flow in the opposite direction. This is called a check valve, as it prevents or "checks" the flow in one direction. ...
Valves are found in virtually every industrial process, including water & sewage processing, mining, power generation, processing of oil, gas & petroleum, food manufacturing, chemical & plastic manufacturing and many other fields. ...
Valves may be operated manually, either by a handle, lever, pedal or wheel. Valves may also be automatic, driven by changes in pressure, temperature, or flow. These changes may act upon a diaphragm or a piston which in turn activates the valve, examples of this type of valve found commonly are safety valves fitted to hot water systems or boilers.
More complex control systems using valves requiring automatic control based on an external input (i.e., regulating flow through a pipe to a changing set point) require an actuator. An actuator will stroke the valve depending on its input and set-up, allowing the valve to be positioned accurately, and allowing control over a variety of requirements." [Valve. Wikipedia]
The example "Design elements - Valves and fittings" was created using the ConceptDraw PRO diagramming and vector drawing software extended with the Chemical and Process Engineering solution from the Engineering area of ConceptDraw Solution Park.
Valves and fittings symbols
Valves and fittings symbols, wedge gate valve, valve manifold, tundish, swivel joint, strainer, stop check valve, soldered, solvent, socket, spigot, socket, spigot, socket weld, sleeve joint, separator, screwed sleeve, screwed joint, screw-down valve, screw-down check valve, relief valve, relief angle valve vacuum, relief angle valve pressure, reel valve, reducing valve, reducer, powered valve, plug valve straight through, plug valve T point, plug valve L point, plug valve 3 way, plug valve, parallel slide valve, open vent, needle valve, lock-shield valve, liquid seal, joint, hydrant, globe valve, gate valve, float operated valve, flanged valve, flanged joint, bolted joint, flame arrester, exhaust silencer, exhaust head, end cap socket and spigot, end cap screwed, end cap quick release, end cap flanged and bolted, end cap fillet welded, end cap butt welded, end cap screwed and plugged, end cap, electrically insulated, electrically bonded, drain silencer, diaphragm valve, check valve, characterized port valve, butterfly valve, butt weld, bursting disc, bell mouth, ball valve, angle valve, Y strainer, 3-way plug valve,
Used Solutions

Building Drawing Software for Designing Plumbing

Building Drawing Software for Designing Plumbing
The construction project for any building obligatory must include the plans for systems of water supplying, sewerage, lighting and heating. From one side these are the documents required and indispensable for the construction, but from the other side this is a way of correct and effective selection of equipment, and subsequent its installation. Correctly performed calculations for these systems ensure a reliable, energy-efficient and cost-effective work. At this each project is fully individual decision taking into account all nuances - from the features of building to the personal preferences. ConceptDraw DIAGRAM is a powerful building drawing software for designing Plumbing, Piping, Lighting and other building plans thanks to the included Plumbing and Piping Plans solution and other solutions from Building Plans area. Plumbing and Piping Plans solution includes variety of libraries with different design elements of pipes, valves and other sanitary equipment and helps easy develop the annotated schematics and diagrams of plumbing systems, piping, and waste water.

Building Drawing Software for Design Piping Plan

Use building drawing software to develop the annotated diagrams or schematics of waste water disposal systems, hot and cold water supply systems, water lines and waste water engineering.
The vector stencils library "Valves and fittings" contains 104 symbols of valve components.
Use these icons for drawing industrial piping systems; process, vacuum, and fluids piping; hydraulics piping; air and gas piping; materials distribution; and liquid transfer systems in the ConceptDraw PRO software extended with the Chemical and Process Engineering solution from the Chemical and Process Engineering area of ConceptDraw Solution Park.
www.conceptdraw.com/ solution-park/ engineering-chemical-process
Electrically bonded
Electrically bonded, electrically bonded,
Bursting disc
Bursting disc, bursting disc,
Flame arrester
Flame arrester, flame arrester,
Strainer
Strainer, strainer,
Separator
Separator, separator,
Exhaust silencer
Exhaust silencer, exhaust silencer,
Bell mouth
Bell mouth, bell mouth,
Exhaust head
Exhaust head, exhaust head,
Hydrant
Hydrant, hydrant,
Drain silencer
Drain silencer, drain silencer,
Liquid seal open/closed
Liquid seal open/closed, liquid seal,
Y strainer
Y strainer, Y strainer,
Gate valve
Gate valve, gate valve,
Globe valve
Globe valve, globe valve,
Globe valve 2
Globe valve 2, gate valve,
Globe valve 3
Globe valve 3, gate valve,
Screw-down valve
Screw-down valve, screw-down valve,
Lock-shield valve
Lock-shield valve, lock-shield valve,
Reel valve
Reel valve, reel valve,
Check valve
Check valve, check valve,
Check valve 2
Check valve 2, check valve,
Check valve 3
Check valve 3, check valve,
Screw-down check valve
Screw-down check valve, screw-down check valve,
Stop check valve
Stop check valve, stop check valve,
Diaphragm valve
Diaphragm valve, diaphragm valve,
Diaphragm valve 2
Diaphragm valve 2, diaphragm valve,
Diaphragm valve 3
Diaphragm valve 3, diaphragm valve,
Powered valve
Powered valve, powered valve,
Powered valve 2
Powered valve 2, powered valve,
Powered valve 3
Powered valve 3, powered valve,
Needle valve
Needle valve, needle valve,
Needle valve 2
Needle valve 2, needle valve,
Needle valve 3
Needle valve 3, needle valve,
Relief valve
Relief valve, relief valve,
Relief valve 2
Relief valve 2, relief valve,
Relief valve 3
Relief valve 3, relief valve,
Angle valve
Angle valve, angle valve,
Angle valve 2
Angle valve 2, angle valve,
Angle valve 3
Angle valve 3, angle valve,
Angle valve 4
Angle valve 4, angle valve,
Float operated valve
Float operated valve, float operated valve,
Float operated valve 2
Float operated valve 2, float operated valve,
Flanged valve
Flanged valve, flanged valve,
Butterfly valve
Butterfly valve, butterfly valve,
Butterfly valve 2
Butterfly valve 2, butterfly valve,
Wedge gate valve
Wedge gate valve, wedge gate valve,
Parallel slide valve
Parallel slide valve, parallel slide valve,
Ball valve
Ball valve,
Ball valve 2
Ball valve 2, ball valve,
Ball valve 3
Ball valve 3, ball valve,
Relief angle valve vacuum
Relief angle valve vacuum, relief angle valve vacuum,
Relief angle valve pressure
Relief angle valve pressure, relief angle valve pressure,
Reducing valve
Reducing valve, reducing valve,
Reducing valve 2
Reducing valve 2, reducing valve,
Plug valve 3 way
Plug valve 3 way, plug valve 3 way,
Plug valve L point
Plug valve L point, plug valve L point,
Plug valve 2
Plug valve 2, plug valve,
Plug valve
Plug valve, plug valve,
Plug valve straight through
Plug valve straight through, plug valve straight through,
Plug valve T point
Plug valve T point, plug valve T point,
3-way plug valve
3-way plug valve, 3-way plug valve,
3-way plug valve 2
3-way plug valve 2, 3-way plug valve,
3-way plug valve 3
3-way plug valve 3, 3-way plug valve,
Mixing valve
Mixing valve,
Valve Manifold
Valve Manifold, valve manifold,
Characterized port valve
Characterized port valve, characterized port valve,
Reducer
Reducer, reducer,
Reducer 2
Reducer 2, reducer,
General joint
General joint, joint,
Butt weld
Butt weld, butt weld,
Butt weld 2
Butt weld 2, butt weld,
Butt weld 3
Butt weld 3,
Butt weld 4
Butt weld 4, butt weld,
Flanged/ bolted
Flanged/ bolted, flanged joint, bolted joint,
Soldered / solvent
Soldered / solvent,
Soldered / solvent 2
Soldered / solvent 2, soldered, solvent,
Screwed joint
Screwed joint, screwed joint,
Screwed joint 2
Screwed joint 2, screwed joint,
Screwed joint 3
Screwed joint 3, screwed joint,
Socket and spigot
Socket and spigot, socket, spigot,
Socket and spigot 2
Socket and spigot 2, socket, spigot,
Socket and spigot 3
Socket and spigot 3, socket, spigot,
Sleeve
Sleeve, sleeve joint,
Sleeve 2
Sleeve 2,
Screwed sleeve
Screwed sleeve, screwed sleeve,
Screwed sleeve 2
Screwed sleeve 2,
Socket weld
Socket weld,
Socket weld 2
Socket weld 2, socket weld,
Swivel joint
Swivel joint, swivel joint,
Swivel joint 2
Swivel joint 2, swivel joint,
Swivel joint 3
Swivel joint 3, swivel joint,
End cap
End cap, end cap,
End cap butt welded
End cap butt welded, end cap butt welded,
End cap screwed
End cap screwed, end cap screwed,
End cap socket and spigot
End cap socket and spigot, end cap socket and spigot,
End cap fillet welded
End cap fillet welded, end cap fillet welded,
End cap screwed and plugged
End cap screwed and plugged, end cap screwed and plugged,
End cap quick release
End cap quick release, end cap quick release,
End cap flanged and bolted
End cap flanged and bolted, end cap flanged and bolted,
End cap flanged and bolted 2
End cap flanged and bolted 2, end cap flanged and bolted,
Electrically insulated
Electrically insulated, electrically insulated,
Tundish
Tundish, tundish,
Syphon drain
Syphon drain,
Open vent
Open vent, open vent,
Used Solutions

Building Drawing. Design Element: Piping Plan

When you are going to build a house or to make repairs of new built home, apartment, office, shop, or to renovate any other premises, in many cases you will need to make the package of drawings, plans and documents, including the such important plans as the Overall floor plan, Interior design plan, Ceiling plan, Electrical system plan, and of course the Plumbing plan, Water supply system plan, and Piping Plan. When choosing between the modern software for building construction, planning and design, we recommend you to select the multifunctional building plan software ConceptDraw DIAGRAM enhanced with Plumbing and Piping Plans solution from the Building Plans area of ConceptDraw Solution Park. This solution provides large variety of examples, samples, quick-start templates and libraries of pipes, plumbing and valves vector design elements for design and construction the Plumbing and Piping Plans, schematics and annotated diagrams for hot and cold water supply systems, water lines and waste water disposal systems.